Key points for installation of quick-install integrated wall decorationKey points for installation of quick-install integrated wall decoration
With the higher and higher living standards, people have higher and higher requirements for home decoration. The integrated wall decoration, which combines many advantages, is gradually welcomed by more and more consumers, and has become the mainstream product of home decoration. So what should we pay attention to during the installation?
1. Prepare materials
Art knife, desktop cutting machine (select high-speed sawtooth saw blade), grinding machine (serrated saw blade), square ruler, tape measure, triangular file, jig saw, 3P air pump, air gun, cement straight nail gun, wood square: It is mainly used in the structural part of the top return band. Wood board: mainly used in the background wall. Corner line: Some corners are closed.
2. Installation, measurement and calculation
The wall area used for home improvement is estimated to be 3 times the floor area, which basically includes the wall and the top. The basic installation area is within this area. Accounting method for measuring the actual area of households: based on the actual measured area, and after completing the return band, it is basically guaranteed that the height from the top to the ground should not be less than 2.75M, so that after the calculation, the maximum amount can be guaranteed during the installation process. Consumers bring unnecessary losses.
3. Preparation and calculation
2 spare materials are guaranteed in the same wall. The background wall needs to be spliced with a large amount of 0.5 square meters of extra material.
4. Construction steps
Top light strip and wooden structure of background wall: Make wooden structure according to the design requirements, and pay attention to the matters during operation. The structure made by wood has enough points for fixing the integrated wall panel; Straight; try to make the size of the two sides at the right angle consistent; the structure is relatively solid; after the wooden structure is completed, perform the actual wiring and reserve the electrical wiring port. Water pipe layout and floor installation. Install the integrated wall panel on the top. Generally, the integrated wall panel is installed from the top during the installation process. During the cutting process, the material must be flat and free of burrs. The higher the speed of the cutting saw, the fewer burrs. The measurement size must be within the error of 2MM, otherwise the stitching will be very uneven. Wall and background wall installation, during this installation process, if using female corner line, anchor line, waist line, door cover line, window cover line, etc., the line installation line is installed in the integrated wall panel.
Integrated wall decoration
5. Details of installation processing
Bending at right angles. During the bending process, the thickness of the wall must be included in the bending line (for example: the column is bent at right angles, the first piece of material is 5CM away from the right angle, the bending line is in the protruding part, the bending line should be At 5.8CM, and so on.) Pay attention to the bending process, first draw the bending line, and then take the polyurethane material, generally around 8MM. Keep the bend as straight as possible. Concave and convex board 45-degree splicing: After the plate is cut at 45 degrees, the burrs are flattened and then spliced. Note that the right angle is neatly stitched as shown in the figure: the right-angle splicing of the concave and convex board: the inside of the splicing board is polished at a 45-degree angle for insertion, and the splicing board is directly inserted into the slot of another sheet. Pay attention to the angle control when grinding. Concave and convex board inner corner splicing: the splicing board is polished at a 45-degree angle for insertion, and the splicing board is directly inserted into the slot of another sheet. Pay attention to angle control when grinding, the principle is the same as right angle splicing.
6. Acceptance standards
Flat material joints are neat; the closing part does not affect the appearance; the material is firmly fixed, and there is no void in the material at the wall; the color matching is reasonable; the internal insulation layer has no leakage; the wave board is completely connected without burrs; whether the folding is at a right angle, Whether it is smooth, flat and beautiful.
Today's consumer market, whether it is integrated wall panels or other aspects, is welcoming the newly rising post-80s and 90s consumers. Faced with this group of new human beings that have grown up with the information age, currently, the integration of integrated wallboard products is serious. With the improvement of material living standards, people have higher and stricter requirements on the variety, function and use of integrated wallboards, and the degree of recognition of the brand is also increasing. With the development of the construction industry, the interior decoration industry will have greater development, and integrated wall panels as one of the important materials for interior decoration will also develop. The three major decoration giants, roof, wall and floor, are indispensable for any one. Integrating the diverse styles, simple installation and strength and quality of the wall panel, they have made great use in the wall industry.
If you want to know more about it please do not hesitate to contact me. WhatsApp:+86-15966835076.